← All experiments

Experiment

Build a giant kettle

Boil water, spin a turbine, turn a generator. Build it wrong first: a kettle aimed at a fan that barely lights a bulb. Then find the clever part, at the cold end.

From the Short "About Half the World's Electricity Comes From Giant Kettles". ▶ Watch the Short

A power station laid out on a table: a kettle on a flame aimed at a fan, which later becomes a sealed boiler feeding steam through a turbine. The turbine's shaft turns a generator, a magnet inside coils of wire, wired to a light bulb. The used steam goes out into the air or into a box of cold-water pipes. fan generator

Boil a kettle at a fan

Boil water and aim the steam at a fan. The fan spins a generator: a magnet turning inside coils of wire, which pushes electricity along them to a bulb.

Boil the kettle, then turn the flame up to High. How bright does the bulb get?

Flame

Water20 °C
Steam pressure1 atm
Steam hitting the fan–
BulbOff

What's going on

A generator turns a magnet (in big ones, an electromagnet) inside coils of wire; the moving magnetic field pushes electricity along the wire. Something has to turn it, and in coal, nuclear and many gas plants that something is steam. Add them up and about half the world's electricity comes from these giant kettles: in 2024 coal made 34% of it and nuclear 9%, almost all by steam, and part of gas's 22% came from steam too. Dams, wind and solar panels don't boil water.

A kettle aimed at a fan wastes most of its steam: it puffs out everywhere and misses the blades. A power station seals the water in a boiler, so the steam is at high pressure and far hotter than a kettle's 100 °C: roughly 280 °C in most nuclear plants, and up to about 600 °C in modern coal plants. It drives a turbine, rows of blades on one shaft. The steam expands as it goes through, so each row is bigger; in big turbines the last blades can be more than a metre long. Never seal a real kettle or any container on a heat source: it can burst. A power station's boiler is thick steel, with safety valves.

The real trick is the cold end. Let the used steam out into the air and the exit sits at the air's full pressure, 1 atmosphere, and the higher the pressure at the exit, the less work the steam can do. Old steam locomotives worked that way. A condenser cools the steam on pipes of cold water, and water takes up tens of thousands of times less room than the steam it came from, so the turbine's far end sits at about a twentieth of normal air pressure. Strictly, a vacuum doesn't pull: the steam is driven by the difference in pressure between the two ends, and the condenser removes almost all of the pressure that would push back. So in effect it's pulled. The same steam does roughly a third more work.

The boiler water and the cooling water are separate loops, so the clean boiler water is pumped back and used again. The warmed cooling water is cooled in a tower, or by a river, lake or the sea. Only about a third to a half of the heat becomes electricity; the rest leaves through the cold end. That isn't poor design: a heat engine has to dump some heat at a cold end to work at all.

In many gas plants, a jet-engine-like gas turbine makes about two thirds of the power directly, and its hot exhaust boils water for a steam turbine that makes the rest. Some gas plants have no steam part at all.

In the readouts, atm means atmospheres (1 atm is normal air pressure) and kJ means kilojoules (1 kJ is about the work of lifting 100 kg one metre). Simplified: the plant is a picture of the idea, not a real one, and time is sped up. The kettle is 1.7 litres on a gas ring; the share of its steam hitting the fan is counted from the drawing's puffs. The boiler's pressure climbs in seconds; on the way up the temperature shown is water's boiling point at that pressure, and the last climb to 540 °C stands for the steam being heated further. The work from each kilogram of steam is for an ideal turbine with no losses, worked out from steam tables for steam at 160 times normal air pressure and 540 °C, so real turbines get less, and the exact gain from the condenser depends on the plant. Here more work makes the turbine spin faster and the bulb brighter; a real station's turbine turns at a steady speed and gives more power instead. In step 4 every heat source makes the same steam; real nuclear plants run cooler steam, and their boilers and turbines differ in detail. The warmed cooling water is drawn orange to show it's warmer, though it's only a little warmer.